AVCO-CLEAR NF-PC is a synthetic thickener for pigment printing, formulated specially for producing sharp designs when printing polyester cotton fabrics.Printing pastes prepared with AVCO-CLEAR NF-PC is producing excellent level and even prints, with higher color yield and brilliancy.
SPECIFICATION:
Appearance |
Slightly viscous white liquid. |
Chemical nature |
Poly acrylic acid copolymer dispersion in inert oils with special surfactants. |
Compatibility |
- Compatible with nonionic and anionic products usually used in pigment printing.
- Do not mix with strong acids, strong alkalis and with cationic products.
|
Ionicity |
Anionic |
pH (1% dispersion) |
5.5 – 6.5 |
Solubility |
Dispersible in water with an high speed mixer to a thick paste at concentration of 1.5-2.0% |
Storage |
Do not store in direct sun, and in hot places. When properly stored, storage stability is 12 months at least. If the product freezes.It can be reused after thawing and mixing |
PROPERTIES & USES:
- High quality thickener, producing sharp and bright prints when printing polyester
cotton fabrics.
- The printing paste produced with AVCO-CLEAR NF-PC is non flushing out the print
borders even when drying in the air.
- Does not impair the hand of printed fabrics.
- Suitable for flat and rotary screen printing processes.
- Suitable for all kinds of textile fabrics.
- Suitable for all-aqueous and for oil-in-water printing pastes.
- Very good coverage and levelness of printed area, with excellent brilliancy and
superior colour value.
- When using AVCO-CLEAR NF-PC it is not necessary to add an acid catalyst to the
print paste. After drying the active matter of the thickener acts as the
catalyst.
- Excellent reproducibility.
- Printing paste preparation is easy and rapid.
- AVCO-CLEAR NF-PC is less sensitive to water hardness and to electrolytes.
- AVCO-CLEAR NF-PC does not block pumps, pipes and screens.
- During paste preparation and the printing process AVCO-CLEAR NF-PC does not
release hazardous vapours of solvents to the environment.
APPLICATION:
Printing paste preparation:
The following is a typical formulation:
gr/kg |
Remarks |
Water |
adjust to 1000 |
Use soft water |
AVCO-ANTIFOAM PR |
0-3 |
Important when printing large area |
AVCO-CLEAR NF-PC |
18-22 |
Adjust to the needed viscosity |
AVCO-BINDER SPC |
60-180 |
Usage depends on quantity of pigment |
AVCO-PRINTOSIL EM |
0-10 |
Softener |
AVCO-PRINTFIX L |
0-6 |
Cross-linking agent |
AMMONIA SOLUTION |
1-3 |
Adjust pH to 7.5-8.5 |
AVCOLOR PIGMENTS |
X |
Depends on required shade |
AVCO-CLEAR NF-PC can be used with all common aqueous binders used in textile printing.
When used with AVCO-BINDER SPC the consumption of the thickener is lower, and the coverage and the brightness of the print are better.
PREPARATION METHOD:
The thickener is added to the water, and homogenized with an high speed (1500-3000 r.p.m.) homogenizer mixer for 10 minutes.
Add all other ingredients in the same order as in the recipe above.
The pH of all the final paste should be 7.5-8.5 Adjust it by adding ammonia solution.
Final viscosity for solvent free paste should be 70-90 dPa.S, for white spirit emulsions viscosity can be lowered to 60-70 dPa.S (Haake viscosimeter VT-02).
REMARKS:
-
Add all ingredients in the same order as in the recipe above. Adjust pH with ammonia if needed.
-
When preparing a solvent containing paste, the white spirit should be added in small portions in order to get a homogeneous paste. Consumption of the thickener is lower.
-
The required viscosity depends upon the printing machine type, type of fabric and the print design.
-
If viscosity of the paste is too high, viscosity can be reduced with electrolytes such as ammonium salts.
-
If viscosity of the paste is too low adjust it by adding more AVCO-CLEAR NF-PC and continue mixing for additional 4-6 minutes.
-
If printing paste has to be stored for prolonged times add 1-2 gr/kg of a preserving agent (AVCOGARD PR).
-
Prepare printing paste with softened water. If water are hard, it is advisable to use a non-alkaline sequestering agent (AVCO-POLYQUEST KAL). Viscosity of paste may be impaired, and higher quantities of thickener are needed.
-
The printing paste is sensitive to electrolytes. When adding electrolytes to the paste, amount of thickener should be increased to receive the desired viscosity.
-
AVCO-PRINTOSIL EM is a silicone softener used to improve flexibility of the binder film.
-
AVCO-PRINTFIX L is a cross linking agent, used to improve wash fastness and wet rubbing fastness.
|